Best PC Cases for Video Editing: 10 Top Picks

The Vector V100 comes with 4 pre-installed 120mm ARGB PWM fans using hydraulic bearings, each capable of up to 1800 RPM, 61.47-60.4 CFM airflow, and 2.54-2.17 mm-H2O air pressure, with noise ranging 26.5-30.8 dBA depending on speed. A 26-LED ARGB strip adds further lighting, and both fans and strip daisy-chain together for a simpler cable run than wiring each component separately.

• 4x 120mm ARGB PWM fans included, hydraulic bearing design
• 26-LED ARGB strip with full spectrum color control
• Daisy-chain connectivity reduces individual cable runs

Fan and strip lighting sync with motherboard ARGB software, so color and effects can match other components already running compatible lighting ecosystems.

The case supports ATX, Micro-ATX, Mini-ITX, and back-connect ATX or Micro-ATX motherboards, giving builders the option of a standard layout or a back-connect board for hidden cable routing behind the tray. Tool-less mounting on each side panel speeds up the build process, since panels come off without reaching for a screwdriver for routine access.

• Back-connect motherboard support for cleaner cable management
• Tool-less side panel mounting mechanism
• Included GPU support bracket for heavier graphics cards

E-ATX and other oversized motherboard formats are not on the supported list, so builders working with larger boards will need to confirm fit before assembling the rest of the build.

Internal clearance is built for high-end hardware: graphics cards up to 420mm, CPU air coolers up to 178mm tall, and a top-mounted radiator up to 360mm. That headroom leaves room to move from air cooling to a 360mm liquid loop, or to swap in a longer flagship GPU later, without the case itself becoming the limiting factor.

• 420mm max GPU length clearance
• 178mm max CPU cooler height
• 360mm top radiator support

A GPU support bracket is included to help offset the weight of longer graphics cards over time, reducing sag as heavier cards are installed.

This ATX mid tower measures roughly 17.6 inches deep, 8.46 inches wide and 18.46 inches tall, and combines a metal frame with a genuine walnut or oak wood front panel and a tempered glass side panel for viewing internal components. Two 140mm PWM fans come pre-installed, giving a working airflow setup before adding any aftermarket cooling.

• Metal frame paired with genuine wood front panel accents, cut from sustainably sourced walnut or oak
• Tempered glass side panel resists scratching while showing off internal components
• 2 pre-installed 140mm PWM fans provide baseline airflow without extra purchases

Front panel access uses an open-mesh design behind the wood slats for intake airflow, rather than a fully solid wood front that would restrict air movement.

The case supports ATX, mATX, and ITX motherboards in one shared layout, and GPUs up to 355mm in length fit with a standard configuration. Installing a 360mm radiator in the front reduces available GPU clearance to 300mm, so radiator size and GPU length need to be balanced against each other during planning.

• 355mm maximum GPU length in standard configuration without a front radiator
• 300mm GPU clearance remains available even with a 360mm front radiator installed
• 7 bridgeless expansion slots support multi-card or angled component layouts

Because GPU clearance changes depending on front radiator size, builders planning a large air-cooled GPU alongside front liquid cooling should measure both components against the case's clearance figures before buying.

Storage starts with 2 combined 3.5-inch/2.5-inch drive mounts plus 2 dedicated 2.5-inch mounts, covering a mix of traditional hard drives and SSDs without needing extra brackets. A front Type-C USB port supports newer peripherals and fast external transfers directly from the case front panel, and the interior layout leaves room for additional fans or radiators as a build's cooling needs grow.

• 4 total drive mounts, 2 combined plus 2 dedicated 2.5-inch, support a mixed HDD/SSD setup
• Front-panel USB Type-C port supports modern peripheral connections
• Removable side panels and a clip-off top panel simplify future internal upgrades

Because the drive mount count is fixed rather than expandable, builds needing more than 4 total drives will need external storage or a different case.

Three 120 mm addressable PWM fans ship pre-installed behind a perforated steel front panel. The perforation uses a three-dimensional Y pattern designed to give air a low-obstruction path rather than forcing it through a flat mesh grille.

• Front rails take fans up to 200 mm
• Roof rails take fans up to 140 mm
• Side mounting available once the inner panel is removed
• Fans support a Zero RPM mode for near-silent behaviour at low load

The rail system is the useful part. Rather than fixed screw holes, the rails let you slide a fan to sit exactly over a graphics card or a radiator inlet. If you are running a high-power card, adding a rear exhaust fan is the first upgrade worth making, since all three included fans are intake.

This is a mid-tower ATX chassis built from alloy steel with aluminium elements, sized for a mainstream tower build rather than an extended workstation board.

• Supports ATX, micro ATX and mini ITX boards
• Supports rear-connector boards: ASUS BTF, MSI Project Zero, Gigabyte Stealth
• Roof radiator mounting up to 140 mm fan sizes
• The internal side panel doubles as a cable cover or a fan mount

Back-connect board support is the detail worth flagging. Those boards move every connector to the rear of the tray, which needs matching pass-through cut-outs in the case to work at all. If you are planning that style of build, this chassis is already prepared for it. For a conventional board, the same cut-outs simply serve as generous cable routing.

The distinguishing idea here is a chassis assembled from replaceable sections rather than a single riveted shell. Panels, the board tray and the front input panel are designed to come off and be swapped for alternatives.

• The motherboard tray can be exchanged for a billet aluminium version
• The front input panel can be swapped for one with a different port arrangement
• Side panels and rails come apart for access during a build

Two things follow from that. Building is easier, because you can strip the case back to a skeleton and reassemble around the components. And the case can change later without being replaced. The trade is that every alternative module is bought separately, so the version in the box is what you get until you choose to add to it.

The NZXT H5 Flow - Compact ATX Mid-Tower PC Case - Black provides essential hardware performance for custom PC builds and workstation upgrades. Engineered to manage demanding electrical or thermal workloads, this model incorporates EXCEPTIONAL GPU COOLING-The PSU shroud is perforated on the side and together with LARGE RADIATOR SUPPORT-Supports up to a 360mm radiator in front and a. PC builders and system integrators will benefit from the efficient internal layout, which simplifies system assembly while supporting high operational stability. The design helps maintain consistent hardware responsiveness across intensive computing tasks, gaming sessions, and daily multitasking workloads. Physical dimensions measuring 8.86"D x 16.93"W x 18.31"H allow for straightforward spatial planning prior to final placement.

Built using resilient structural components, this unit features a sturdy outer housing engineered to resist operational wear. Precision manufacturing ensures that all joints and surface connections remain firmly aligned during regular daily activity. HIGH-PERFORMANCE AIRFLOW-Ultra-fine mesh on the top, front, and side reinforces overall physical stability over extended service periods. Premium Metal construction maintains structural integrity and cosmetic appearance under routine handling. Structural integrity remains firm throughout regular usage, giving owners peace of mind. Maintaining adequate interior case airflow and clean ventilation ports preserves peak hardware efficiency during heavy processing workloads.

Initial setup requires placing the unit on a flat, stable surface with adequate clearance around all sides for proper operation. Ensure all power or connection cables are routed neatly without sharp bends to prevent wire strain. Regular care involves wiping exterior housing surfaces with a soft cloth to remove dust buildup. Inspecting mechanical connections periodically preserves operational efficiency and maintains cosmetic appearance over time. Maintaining adequate interior case airflow and clean ventilation ports preserves peak hardware efficiency during heavy processing workloads. Integrating this reliable component into your computer system ensures stable power delivery and long-term electrical protection.

The Antec Performance 1 FT Full Tower RTX40 Fully Compatible provides essential hardware performance for custom PC builds and workstation upgrades. Engineered to manage demanding electrical or thermal workloads, this model incorporates Temperature Display Glance at your system status. together with Antec iUnity Provides instant data on PC specs.. PC builders and system integrators will benefit from the efficient internal layout, which simplifies system assembly while supporting high operational stability. The design helps maintain consistent hardware responsiveness across intensive computing tasks, gaming sessions, and daily multitasking workloads. Physical dimensions measuring 20.55"D x 9.06"W x 20.55"H allow for straightforward spatial planning prior to final placement.

Built using resilient structural components, this unit features a sturdy outer housing engineered to resist operational wear. Precision manufacturing ensures that all joints and surface connections remain firmly aligned during regular daily activity. 2 Cable Covers Included for Optimizing the Cable Routing. reinforces overall physical stability over extended service periods. Premium Tempered Glass construction maintains structural integrity and cosmetic appearance under routine handling. Structural integrity remains firm throughout regular usage, giving owners peace of mind. Maintaining adequate interior case airflow and clean ventilation ports preserves peak hardware efficiency during heavy processing workloads.

Initial setup requires placing the unit on a flat, stable surface with adequate clearance around all sides for proper operation. Ensure all power or connection cables are routed neatly without sharp bends to prevent wire strain. Regular care involves wiping exterior housing surfaces with a soft cloth to remove dust buildup. Inspecting mechanical connections periodically preserves operational efficiency and maintains cosmetic appearance over time. Maintaining adequate interior case airflow and clean ventilation ports preserves peak hardware efficiency during heavy processing workloads. Integrating this reliable component into your computer system ensures stable power delivery and long-term electrical protection.

The H9 Flow RGB+ measures 20.08 x 19.29 x 12.6 inches and uses a dual-chamber layout built from alloy steel with wraparound tempered glass panels. It ships with 7 RGB fans pre-installed: six 140mm F420 RGB Core units and one 120mm F120 RGB Core fan in the rear, all managed through an included NZXT Control Hub.

• Total fan capacity reaches 10 fans: up to nine 140mm across the top, front-right and bottom, plus one 120mm at the rear.
• Perforated steel panels and angled front-right fans are positioned for airflow rather than pure aesthetics.
• Extra-wide cable channels and Velcro straps are built in for cable management.

The dual-chamber design keeps the PSU and drive bays visually and thermally separated from the CPU and GPU area, which most single-chamber cases don't offer.

This case fits standard ATX motherboards and supports back-connect boards like ASUS BTF and MSI Project Zero for a cable-free front panel look, in addition to conventional layouts. Graphics card clearance extends to 435mm, enough room for the largest current flagship GPUs without trimming cables or repositioning drive cages.

• Radiator support reaches 420mm on both the top and front-right panels for large liquid cooling loops.
• Standard motherboards without back-connect headers install normally, just without the cable-free routing benefit.
• The included Control Hub manages fan and RGB connections without needing a separate motherboard RGB header for each fan.

Before buying a back-connect motherboard specifically for this case, confirm the board's connector layout matches NZXT's supported back-connect standard rather than assuming universal compatibility.

With 10-fan capacity and support for up to a 420mm radiator on 2 separate panels, this case leaves significant room to add cooling hardware well beyond the 7 fans included at purchase. The dual-chamber layout also gives space to add extra drives or a bigger PSU later without redoing the whole build.

• Mesh panels are designed to maximize airflow while still filtering out dust.
• Extra-wide cable channels and tie-down points make future component swaps easier to route cleanly.
• GPU clearance of 435mm covers essentially any current graphics card upgrade.

Because the case already ships fully populated with 7 fans, later upgrades are more about swapping in a bigger radiator or additional storage than adding basic case cooling.

The shell measures 15.35 inches deep, 8.07 inches wide and 18.98 inches tall, the standard mid-tower envelope for a full ATX motherboard. Micro-ATX and mini-ITX boards drop onto the same standoffs, leaving spare room behind the tray for cable routing. Steel forms the frame and tempered glass the left panel, so the empty chassis has real mass before any hardware goes in. Front I/O covers two USB 3.0 ports plus audio, enough for a headset and an external drive without reaching behind the desk. Three numbers are worth checking before ordering: graphics card length, CPU cooler height and radiator thickness. The polygonal mesh front means intake is not choked by a solid door, but a 360 mm radiator with thick fans still deserves measuring against your board layout.

Six PWM ARGB fans arrive already mounted, which is unusual since most mid-towers ship with one or two. Two separate things need controlling:

• PWM speed runs from motherboard fan headers, so the fans idle slowly and ramp under load instead of spinning flat out all day.
• Addressable lighting needs a 3-pin 5 V ARGB header. Each fan then addresses 16.8 million colours through your board maker software.

Boards carrying only a 4-pin 12 V RGB header cannot drive addressable fans; lighting will default to a fixed pattern or need a separate controller. Count headers first, because six fans plus a CPU cooler is more connectors than many entry boards provide, and a PWM splitter hub is the simple fix. Upgraded bearings are quoted for service life, and the frames are standard 120 mm if you swap them later.

The side glass hangs on magnets with a metal pull ring, so it swings open like a door rather than needing four thumbscrews removed and a heavy panel balanced against the desk. That changes maintenance habits: a monthly wipe of the graphics card shroud and a blast through the front mesh becomes a two-minute job instead of a weekend chore. Dust filters still need pulling and rinsing, and they must be completely dry before refitting. The open door also gives quick access for swapping a card or reseating a memory stick without dragging the tower off the desk. Owners who display figures or models inside the case get the same benefit, since the door opens without disturbing cable routing. Clean the glass with a microfibre cloth, as household sprays can haze the coating over time.

The CORSAIR Frame 4500X LX RGB Link Panoramic Mid-Tower PC provides essential hardware performance for custom PC builds and workstation upgrades. Engineered to manage demanding electrical or thermal workloads, this model incorporates NOTE The following product only includes 3x Pre-Installed Fans and iCUE together with Single-Piece Curved Glass Panel - The front and side panel are made. PC builders and system integrators will benefit from the efficient internal layout, which simplifies system assembly while supporting high operational stability. The design helps maintain consistent hardware responsiveness across intensive computing tasks, gaming sessions, and daily multitasking workloads. Physical dimensions measuring 19.65"D x 10.08"W x 18.54"H allow for straightforward spatial planning prior to final placement.

Built using resilient structural components, this unit features a sturdy outer housing engineered to resist operational wear. Precision manufacturing ensures that all joints and surface connections remain firmly aligned during regular daily activity. Reverse-Rotor RGB Fans The included side-mounted 120mm fans use a reinforces overall physical stability over extended service periods. Premium Plastic, Tempered Glass construction maintains structural integrity and cosmetic appearance under routine handling. Structural integrity remains firm throughout regular usage, giving owners peace of mind. Maintaining adequate interior case airflow and clean ventilation ports preserves peak hardware efficiency during heavy processing workloads.

Initial setup requires placing the unit on a flat, stable surface with adequate clearance around all sides for proper operation. Ensure all power or connection cables are routed neatly without sharp bends to prevent wire strain. Regular care involves wiping exterior housing surfaces with a soft cloth to remove dust buildup. Inspecting mechanical connections periodically preserves operational efficiency and maintains cosmetic appearance over time. Maintaining adequate interior case airflow and clean ventilation ports preserves peak hardware efficiency during heavy processing workloads. Integrating this reliable component into your computer system ensures stable power delivery and long-term electrical protection.

In practical product testing, the MONTECH TG3 ATX Mid Tower PC Case Pre-Installed ARGB demonstrates practical utility and dependable craftsmanship for everyday household tasks. Primary specifications feature SHOWCASE YOUR STYLE Designed with a tiered interior platform TG3 along with PRE-INSTALLED ARGB UNIBODY FANS Includes 1 x GF360 U REV. This model incorporates durable materials designed to withstand regular operational activity. Overall physical measurements of 20.83"D x 18.31"W x 9.41"H provide clear boundaries for spatial planning in your room.

• Engineered with SHOWCASE YOUR STYLE Designed with a tiered interior platform TG3 to support efficient daily operation.
• Incorporates PRE-INSTALLED ARGB UNIBODY FANS Includes 1 x GF360 U REV for enhanced structural reliability during routine use.
• Features HIGH-AIRFLOW COOLING PERFORMANCE Ventilated panels optimized airflow pathways and support to ensure practical usability across varied workspace setups.
• Built to maintain consistent operational stability within standard product design conditions.
• Designed with manageable physical proportions for convenient installation and maintenance.

Following standard operation guidelines and maintaining adequate surrounding clearance ensures optimal functional longevity.

The three numbers that decide whether your parts fit are stated plainly, and they are generous for a Micro-ATX chassis.

• GPU length: 360 mm. That covers almost every triple-fan card on the market, including large models.
• CPU cooler height: 159 mm. Enough for most mainstream tower coolers, though the very tallest dual-tower designs will foul the side panel.
• PSU length: 160 mm. Standard ATX units are typically 140 to 160 mm, so measure before choosing a high-wattage or fully modular supply.

Board support covers Micro-ATX and Mini-ITX. A Mini-ITX build in here leaves a lot of empty space but gains easy cable routing. Check graphics card thickness too, since a 3-slot card in a Micro-ATX layout can cover the lower expansion slots.

The design philosophy is open thermal, meaning perforation on every side rather than a sealed front panel with a narrow intake slot.

• Up to five fan positions in total across front, top and rear mounts.
• A 240 mm liquid cooler radiator is supported, which is the practical ceiling for a chassis this size.
• Magnetic dust filters cover the intakes and pull off for a rinse under a tap.

Only one fan comes fitted at the rear, so plan on adding intakes. Two 120 mm fans at the front pulling in, with the stock rear fan exhausting, gives the classic front-to-back path and slight positive pressure that keeps dust on the filters rather than on the components. Clean those filters every couple of months if the case sits on carpet.

The modular I/O panel is the unusual feature. Rather than being fixed at the top front, it can be repositioned to the front, top or bottom on either side of the chassis.

• Case on the floor to your left? Move the ports to the top-right so the leads do not stretch.
• Case on a desk? Front mounting keeps a USB stick within easy reach.

Behind the motherboard tray there is room for cable routing, though it is tighter than a full ATX tower, so a non-modular power supply leaves a bundle of unused leads to hide. The transparent side panel means that mess is visible, so it is worth taking the extra fifteen minutes with cable ties. Standoffs are pre-fitted for the Micro-ATX pattern, which saves a step at the start of the build.